Page 3 of 9
Re: FRN Police 4
Posted: Sun Aug 05, 2018 6:29 am
by steelcity16
crazywednesday wrote: ↑Sat Aug 04, 2018 10:36 pm
Dodge wrote: ↑Fri Aug 03, 2018 7:39 pm
Police Salt!!!!!
But in lc200n serrated so we get the ffg version.
Can H1 not be FFG for some reason?
Re: FRN Police 4
Posted: Sun Aug 05, 2018 6:45 am
by u.w.
steelcity16 wrote: ↑Sun Aug 05, 2018 6:29 am
crazywednesday wrote: ↑Sat Aug 04, 2018 10:36 pm
Dodge wrote: ↑Fri Aug 03, 2018 7:39 pm
Police Salt!!!!!
But in lc200n serrated so we get the ffg version.
Can H1 not be FFG for some reason?
That is my understanding, yes. There's a thread, or some posts, on it somewhere. From what I recall, the work hardening properties of it, (H1) came in to play.
u.w.
Re: FRN Police 4
Posted: Sun Aug 05, 2018 9:33 am
by sal
RadioactiveSpyder wrote: ↑Sat Aug 04, 2018 9:49 pm
Ok Sal, I have a dumb noob question for you: if I held a FRN Police 4 prototype at the OKCA show, where did the tooling for that come from? I only ask because you mentioned the tooling is still being finalized, and the one I held (albeit briefly) seemed spot on. As I said, a totally noob question...
And I’m one of those much in favor of a ZDP version! :D
Cheers, Radioactive :)
It may have been a hand made prototype. If so, it didn't have the bi-directional texture?
We are currently tooling up for three FRN models in Seki. FRN Police 4, Endela and Rock Jumper. I have only seen the Endela handle made from tooling.
sal
Re: FRN Police 4
Posted: Sun Aug 05, 2018 9:36 am
by dj moonbat
What's the Endela?
Re: FRN Police 4
Posted: Sun Aug 05, 2018 9:36 am
by sal
Hi U.w.
Welcome to our forum.
Steelcity,
That is correct. As u.w. mentioned, the work hardening properties prevent flat grinding the steel, except slowly by hand.
sal
Re: FRN Police 4
Posted: Sun Aug 05, 2018 9:37 am
by sal
dj moonbat wrote: ↑Sun Aug 05, 2018 9:36 am
What's the Endela?
A new model in-the-works,
sal
Re: FRN Police 4
Posted: Sun Aug 05, 2018 10:02 am
by Doc Dan
I am going out on a limb and guessing that the Endela is a knife half way between the Delica and the Endura in size?
Re: FRN Police 4
Posted: Sun Aug 05, 2018 10:38 am
by dj moonbat
sal wrote: ↑Sun Aug 05, 2018 9:37 am
dj moonbat wrote: ↑Sun Aug 05, 2018 9:36 am
What's the Endela?
A new model in-the-works,
sal
Re: FRN Police 4
Posted: Sun Aug 05, 2018 10:43 am
by Woodpuppy
Doc Dan wrote: ↑Sun Aug 05, 2018 10:02 am
I am going out on a limb and guessing that the Endela is a knife half way between the Delica and the Endura in size?
If so, Endela sure sounds interesting! Rock jumper sounds like a hawkbill fixed blade? Something to very quickly cut rope?
Re: FRN Police 4
Posted: Sun Aug 05, 2018 11:56 am
by supracor
All of us must immediately see the photo of the Endela... please :p
Re: FRN Police 4
Posted: Sun Aug 05, 2018 1:15 pm
by Knife Knut
sal wrote: ↑Sun Aug 05, 2018 9:36 am
As u.w. mentioned, the work hardening properties prevent flat grinding the steel, except slowly by hand.
sal
I bet a 5 axis waterjet could do it :) , but that would definitely not be economically feasible for production runs.
Re: FRN Police 4
Posted: Sun Aug 05, 2018 1:42 pm
by sal
supracor wrote: ↑Sun Aug 05, 2018 11:56 am
All of us must immediately see the photo of the Endela... please :p
I'll have to see scheduling. Don't like to say too much too early.
sal
Re: FRN Police 4
Posted: Sun Aug 05, 2018 4:35 pm
by supracor
You are right. All in its time :)
Re: FRN Police 4
Posted: Thu Aug 09, 2018 8:20 pm
by Dodge
Sounds like an endura and a delica mix?
Re: FRN Police 4
Posted: Fri Aug 10, 2018 5:00 am
by muddog15
I would like to see black scales and a good to high quality steel will do.
Re: FRN Police 4
Posted: Fri Aug 10, 2018 8:47 am
by sal
First run is usually black FRN / VG-10. Then we go from there.
sal
Re: FRN Police 4
Posted: Fri Aug 10, 2018 11:13 am
by supracor
sal wrote: ↑Fri Aug 10, 2018 8:47 am
VG-210
21 times better than VG 10!
Re: FRN Police 4
Posted: Fri Aug 10, 2018 11:15 am
by Eli Chaps
sal wrote: ↑Sun Aug 05, 2018 1:42 pm
supracor wrote: ↑Sun Aug 05, 2018 11:56 am
All of us must immediately see the photo of the Endela... please :p
I'll have to see scheduling. Don't like to say too much too early.
sal
:eek:
:D
Now this is interesting!!!!
Re: FRN Police 4
Posted: Fri Aug 10, 2018 12:57 pm
by mattman
sal wrote: ↑Sun Aug 05, 2018 1:42 pm
supracor wrote: ↑Sun Aug 05, 2018 11:56 am
All of us must immediately see the photo of the Endela... please :p
I'll have to see scheduling. Don't like to say too much too early.
sal
Subbed!
Re: FRN Police 4
Posted: Fri Aug 10, 2018 1:29 pm
by sal
supracor wrote: ↑Fri Aug 10, 2018 11:13 am
sal wrote: ↑Fri Aug 10, 2018 8:47 am
VG-210
21 times better than VG 10!
Corrected. Thanx for the heads-up.
sal