Hey Sal, what's the HRC on V-TOKU 2?
- Deadboxhero
- Member
- Posts: 2178
- Joined: Tue Mar 01, 2016 4:35 am
- Contact:
Hey Sal, what's the HRC on V-TOKU 2?
Hey Sal, may I ask?
What is the hardness on the V2?
Thanks,
Shawn
What is the hardness on the V2?
Thanks,
Shawn
- Deadboxhero
- Member
- Posts: 2178
- Joined: Tue Mar 01, 2016 4:35 am
- Contact:
- Deadboxhero
- Member
- Posts: 2178
- Joined: Tue Mar 01, 2016 4:35 am
- Contact:
Re: Hey Sal, what's the HRC on V-TOKU 2?
Anyone down to crowd fund some hardness testing? There is a Metallugical lab down the street that quoted $80.
I don't mind the divots on the blade above the edge since I'm going to regrind it thinner later.
I don't mind the divots on the blade above the edge since I'm going to regrind it thinner later.
Re: Hey Sal, what's the HRC on V-TOKU 2?
We're checking. Hard to do on laminates.
sal
sal
- Deadboxhero
- Member
- Posts: 2178
- Joined: Tue Mar 01, 2016 4:35 am
- Contact:
Re: Hey Sal, what's the HRC on V-TOKU 2?
Thanks Sal, copy that.
Re: Hey Sal, what's the HRC on V-TOKU 2?
Any word on this?
-
- Member
- Posts: 558
- Joined: Tue Oct 24, 2017 5:30 pm
Re: Hey Sal, what's the HRC on V-TOKU 2?
BUMP! Any news on testing, sal & co?
Make Knife Grinds Thin Again.
- The Mastiff
- Member
- Posts: 5951
- Joined: Sun Jun 04, 2006 2:53 am
- Location: raleigh nc
Re: Hey Sal, what's the HRC on V-TOKU 2?
The conversation has moved on from V -toku 2 But I'm still impressed with the performance and ease of sharpening with these. I'm glad I bought an extra Endura. I can do anything from a regular edge at fairly low angles to a thin convex and it doesn't complain. It's not meant to be a 10V or Maxamet but for high sharpness EDC use it does really well. I like the low to medium carbide steels for much of my use and I appreciate not having to fight to get steels sharp. Oh, my guess is 60-61 ish but that is only a WAG.
Joe
Joe
-
- Member
- Posts: 558
- Joined: Tue Oct 24, 2017 5:30 pm
Re: Hey Sal, what's the HRC on V-TOKU 2?
Two models yet to be released for this sprint and it's already old news :eek:?! I know most everyone here has moved on to whatever new super steel out-does-them-all; I'm just showing some interest on this topic :D
Make Knife Grinds Thin Again.
- knivesandbooks
- Member
- Posts: 1455
- Joined: Tue Aug 15, 2017 8:43 pm
- Location: Tulsa, OK
Re: Hey Sal, what's the HRC on V-TOKU 2?
This is the type of steel I prefer. I've been enjoying my delica in it. Still like hap40 more but this is good stuff. Getting my 52100 manix tomorrow and I look forward to comparing it to this.
Christ is risen from the dead, trampling down death by death, and on those in the tombs bestowing life!
Re: Hey Sal, what's the HRC on V-TOKU 2?
Please do share ... I’m interestedknivesandbooks wrote: ↑Wed Dec 05, 2018 9:17 pmThis is the type of steel I prefer. I've been enjoying my delica in it. Still like hap40 more but this is good stuff. Getting my 52100 manix tomorrow and I look forward to comparing it to this.
Chris :spyder: