Search:

Type: Posts; User: Bill1170; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    101
    Views
    1,468

    Much as I prefer stain resistant pocket knife...

    Much as I prefer stain resistant pocket knife blades, I have to admit that a sprint run of PM2's in O-1 would sell out in a New York minute. The sad part is that most of these would never rust or...
  2. Replies
    30
    Views
    1,041

    What David said, a hundred times. Support the...

    What David said, a hundred times. Support the good guys.
  3. Replies
    35
    Views
    941

    Probably so the abuse doesn't damage the lock.

    Probably so the abuse doesn't damage the lock.
  4. Replies
    70
    Views
    2,041

    That is a lovely composition, but the cut end of...

    That is a lovely composition, but the cut end of the lemon looks dried out, not freshly cut. Is that intentional?
  5. Jack, Going back to your original idea for a...

    Jack,

    Going back to your original idea for a minute, what about using a Dremel inside the handle scale to rout a channel that accepts a piece of flat metal - like a short length of stainless steel...
  6. Exactly this. I regularly inspect my back lock...

    Exactly this. I regularly inspect my back lock knives for lint build up. This build up happens faster when the knife is carried loose in pocket rather than clipped. The lint collects in the bottom of...
  7. Replies
    27
    Views
    1,054

    I agree that the flexing was much more impressive...

    I agree that the flexing was much more impressive than the knife and keys. Sapphire is the same stuff used in the Sharpmaker rods as the abrasive (in a ceramic matrix). The hardness is much greater...
  8. Replies
    21
    Views
    730

    It was featured in the recent Spyderco Byte email.

    It was featured in the recent Spyderco Byte email.
  9. I've seen rust in the drive recess of type 316...

    I've seen rust in the drive recess of type 316 stainless wood screws. Small particles from the steel driver bit are left in the recess and then rust.
  10. Replies
    81
    Views
    2,152

    Delica was my gateway Spyderco folder,...

    Delica was my gateway Spyderco folder, specifically a saber ground ZDP Delica 4 in BRG FRN. The Delica is still one of my favorite Spydercos.
  11. Replies
    16
    Views
    299

    Poll: I voted mirror for low friction and corrosion. I...

    I voted mirror for low friction and corrosion. I also like the look.
  12. Replies
    58
    Views
    1,690

    This sums up my own views, too. Best tool for the...

    This sums up my own views, too. Best tool for the job, and all that.
  13. Thread: CBN Rods

    by Bill1170
    Replies
    122
    Views
    7,913

    Thanks, Cliff. Very useful information in this...

    Thanks, Cliff. Very useful information in this entire thread.

    Bill
  14. The FFG Delica is very good for slicing. Opinels...

    The FFG Delica is very good for slicing. Opinels and traditional slim folders will do very well, but "noticeably" is hard to evaluate. I have a fruit testing knife that is very long and thin, but not...
  15. Replies
    10
    Views
    441

    Visible light that passes through glass can cause...

    Visible light that passes through glass can cause fading, too. It isn't only UV light that fades colors.
  16. Replies
    32
    Views
    1,334

    I totally agree. Early adult experiences led me...

    I totally agree. Early adult experiences led me to exercise great caution in lending nice things to others.
  17. Poll: Thank you, Cliff. Your comments on CPM M4 were...

    Thank you, Cliff. Your comments on CPM M4 were enlightening. Have you any idea what Rc hardness the competition cutters are run at? I am familiar with influence particle size in cemented carbides has...
  18. Poll: While not a "casual bombshell," this pithy...

    While not a "casual bombshell," this pithy assessment by Sal is incredibly useful knowledge distilled from long experience and determined investigation. Thank you, Sal, for sharing that with us.
  19. Poll: Fascinating discussion. I entered high carbide,...

    Fascinating discussion. I entered high carbide, fine finish in the poll. I cut wood plus many other materials in my work. My favorite folding knife is only offered in high carbide steels.

    Question...
  20. Replies
    147
    Views
    7,479

    I'm also curious to see Sal's refinement of the...

    I'm also curious to see Sal's refinement of the Stretch ergonomics. That is more personally compelling than new handle colors/materials.
  21. This, exactly. Yablanowitz said it better than I...

    This, exactly. Yablanowitz said it better than I could have. I use mine as my everyday work knife and the lock is essentially unchanged in two years of construction use. I don't abuse it, but I use...
  22. Rock Salt.

    Rock Salt.
  23. Replies
    30
    Views
    724

    Agreed. The clip mounting method used on the FRN...

    Agreed. The clip mounting method used on the FRN Salts would also work in linerless G-10, wouldn't it? Just not 4-way.
  24. Thread: Cpm s35v

    by Bill1170
    Replies
    17
    Views
    831

    I've gotten the impression that CPM 154 performs...

    I've gotten the impression that CPM 154 performs like an improved version of VG10, takes a fine edge like VG10, holds it well, higher wear resistance than VG10, good corrosion resistance etc. I have...
  25. Two thoughts. First, can FRN be done in a solid...

    Two thoughts. First, can FRN be done in a solid color with flecks of contrasting material without ruining molds or significantly reducing durability? I was thinking white with mica flakes for a bit...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4