Search:

Type: Posts; User: kwakster; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.07 seconds.

  1. I think i have: Paper Wheels with diamond...

    I think i have: Paper Wheels with diamond compound

    http://www.spyderco.com/forums/showthread.php?52079-Show-those-Edges-!!!!!/page27&highlight=ceramic+knife

    (Post 531)
  2. Those clipper blades are actually very easy to...

    Those clipper blades are actually very easy to sharpen with Spyderco's ceramic benchstones.
    Put the blade on the stone, your index or middle finger on top of the blade in the center, and then just...
  3. Replies
    5
    Views
    312

    Fake Domino, currently for sale on a large Dutch...

    Fake Domino, currently for sale on a large Dutch auction website for 49.95 Euro or about 68.00 US dollars
    Described as a real Spyderco.
    ...
  4. Thread: Fake Techno

    by kwakster
    Replies
    1
    Views
    195

    Fake Techno

    Just spotted this fake "Techno" on a big auction website in the Netherlands, billed as a real Spyderco.
    Offered for 19.95 Euro or a little over 27 US dollars.
    ...
  5. Replies
    5
    Views
    368

    My own Round Eye Knife and Tool (REKAT) Pioneer...

    My own Round Eye Knife and Tool (REKAT) Pioneer II from around the year 2000.
    ...
  6. Replies
    556
    Views
    22,848

    At the last Amsterdam Meet Sal told us that S110V...

    At the last Amsterdam Meet Sal told us that S110V steel ranked lower in the edge holding department than S90V steel.
    I'm still wondering by what margin.
  7. Replies
    21
    Views
    748

    1) Eat fatty fish regularly, if possible daily....

    1) Eat fatty fish regularly, if possible daily.
    Your body's ability to create joint fluid will benefit greatly from it.

    2) Take 1 or 2 glucosamin tablets daily (with chondroitin if you can find...
  8. Replies
    47
    Views
    1,061

    Madrookie also made a smart choil, as by sloping...

    Madrookie also made a smart choil, as by sloping the front corner it won't snag.
  9. Or i use a combination of Tormek & Wicked Edge,...

    Or i use a combination of Tormek & Wicked Edge, like on this Strider DB-L some time ago.
    This is a limited edition of the DB model in CPM-3V steel and made from thinner stock than the usual S30V...
  10. If the edges are not too wide i just use my Paper...

    If the edges are not too wide i just use my Paper Wheels.
    Did these chisel ground edges a while back with a Paper Wheel coated with 15 micron diamond compound, as they both were quite blunt.
    The...
  11. Replies
    30
    Views
    822

    Paper Wheels with diamond compound.

    Paper Wheels with diamond compound.
  12. Replies
    29
    Views
    1,154

    Yep, former Tri-Flow and Blue Lube user here....

    Yep, former Tri-Flow and Blue Lube user here.
    Nano-Oil beats both by miles.
  13. Made this Strider DB-L replica a while ago from...

    Made this Strider DB-L replica a while ago from an old piece of full hard M2 machine hacksaw blade.
    Hardness lies around 65-66 HRC, and the steel is also very wear resistant: it took many hours to...
  14. Replies
    35
    Views
    1,857

    Yes, and it had the elusive stop lock mechanism...

    Yes, and it had the elusive stop lock mechanism built in,
  15. Thread: Another Cut

    by kwakster
    Replies
    25
    Views
    912

    Didn't know the brand "Staaldruppels" It's Dutch...

    Didn't know the brand "Staaldruppels"
    It's Dutch language for "Steel drops" or "Drops of Steel", but i'm sure you know :-)
  16. Replies
    55
    Views
    2,656

    A few days ago i managed to save my Gaggia...

    A few days ago i managed to save my Gaggia Classic espresso machine from the scrapheap (or at least from an expensive repair) with Nano-Oil.
    There's a part inside the machine that's called a...
  17. A few days ago i managed to save my Gaggia...

    A few days ago i managed to save my Gaggia Classic espresso machine from the scrapheap (or at least from an expensive repair) with Nano-Oil.
    There's a part inside the machine that's called a...
  18. K390 would probably do well on the Endura...

    K390 would probably do well on the Endura platform,
  19. Oh yes there is: :D ...

    Oh yes there is: :D

    http://s21.postimg.org/o40gsnq0z/GEDC6048.jpghttp://s21.postimg.org/cg6ey40w3/GEDC6049.jpghttp://s21.postimg.org/opg8xa6bn/GEDC6056.jpg
    ...
  20. Replies
    8
    Views
    751

    I bought 4 x Artu drill bits in 6 mm for about 54...

    I bought 4 x Artu drill bits in 6 mm for about 54 US dollars including shipping from England to the Netherlands.
    Used only one though, so the other 3 i'm currently reselling.
  21. Replies
    8
    Views
    751

    Job done with the help of the Artu drill bit and...

    Job done with the help of the Artu drill bit and the drill press of a very helpful Dutch knifemaker.
    The process worked exactly as i was told by an Australian knifemaker with experience in using...
  22. Replies
    8
    Views
    751

    The 6 mm Artu drill bits arrived, so it was time...

    The 6 mm Artu drill bits arrived, so it was time to try them on the M2 steel.
    The instruction paper said that when the drill bits are to be used on hardened steel to use a drill press with 2000...
  23. Replies
    8
    Views
    751

    Next step is to try to drill the holes for the...

    Next step is to try to drill the holes for the G-10 grips with these speciality drills:

    http://www.youtube.com/watch?v=ZdSim29sStw&feature=youtu.be
  24. Replies
    8
    Views
    751

    Full hard M2 high speed steel knife

    Currently busy making a knife out of a old piece of Sandvik M2 high speed steel machine saw (about 65-66 HRC) with the help of my Tormek T7 wet grinder.
    Since i had a couple of old G10 grips from a...
  25. Currently my only 2 knives in H1 steel, a Pacific...

    Currently my only 2 knives in H1 steel, a Pacific Salt SE and a USN Catcherman:

    http://s29.postimg.org/9ujlyek4z/GEDC6778.jpghttp://s29.postimg.org/qpyqxepv7/GEDC6779.jpg
    ...
Results 1 to 25 of 283
Page 1 of 12 1 2 3 4