Search:

Type: Posts; User: w3tnz; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Cuscadi can make anything if you got the ca$h.

    Cuscadi can make anything if you got the ca$h.
  2. Replies
    11
    Views
    199

    I have roughly illustrated what I was trying to...

    I have roughly illustrated what I was trying to describe, its the only problem I have had with the wicked edge system, I don't use an angle cube because I have my vice mounted to a chopping board and...
  3. Replies
    11
    Views
    199

    I tried to explain this in your other thread but...

    I tried to explain this in your other thread but perhaps it was unclear, your problem sharpening a blade as thick as a sykco is caused by the left side of the vice being static. When you clamp a...
  4. Thread: Techno concerns

    by w3tnz
    Replies
    23
    Views
    616

    There was at least 2 reported cases of techno...

    There was at least 2 reported cases of techno lock slip on this forum alone, but don't let that discourage you from buying one. Not a design fault, just a couple that weren't made quite right and...
  5. Replies
    15
    Views
    448

    The detent is nothing more than a ball, that...

    The detent is nothing more than a ball, that seats into a hole or divot in the blade, under tension of the lockbar, no magic involved. Either the lock bar was over bent in MFG causing excess tension,...
  6. Replies
    15
    Views
    448

    This was brought up a few times, you might be...

    This was brought up a few times, you might be unlucky, but most of the time the detent is not to blame. Because the techno is so small your fingers naturally puts pressure against the lock bar when...
  7. Replies
    29
    Views
    811

    A bit of lint or dirt won't accelerate wear on...

    A bit of lint or dirt won't accelerate wear on steel, not lubricating the moving parts of your knife will however.. you should be cleaning it before anything like that becomes an issue in any case....
  8. Replies
    4
    Views
    121

    LC200N on the tusk..

    LC200N on the tusk..
  9. Replies
    11
    Views
    303

    I'm nearly out of my stock of 10wt, really good...

    I'm nearly out of my stock of 10wt, really good all purpose lubricant, have been using it on my bike and rifle lately. I might buy the 3 pack of applicators to try, mix up etc, but the 10wt has been...
  10. Replies
    8
    Views
    223

    There is a bit of play in the slots, its normal....

    There is a bit of play in the slots, its normal. You could put a rubber band around the top of the stones, it will bring the angle down a touch and stop the rods from moving.
  11. Thread: More Beans!

    by w3tnz
    Replies
    5
    Views
    174

    Looks good man :)

    Looks good man :)
  12. I have done it on a couple of my knives, when the...

    I have done it on a couple of my knives, when the rough surface inside the hole has started to corrode, but don't worry about it otherwise. I don't chamfer the edge, leave it sharp.
  13. Replies
    6
    Views
    211

    The recurve on the pkal is quite subtle, the...

    The recurve on the pkal is quite subtle, the sharpmaker could do it easily using the corners.
  14. New stock on my AR to keep my rifle compliant...

    New stock on my AR to keep my rifle compliant with recent local law changes, it was either this or reclassify the gun, upgrade my security, and not use it for hunting. Under the new law, free...
  15. Replies
    294
    Views
    7,177

    http://i1323.photobucket.com/albums/u596/dkhugh3s/...

    http://i1323.photobucket.com/albums/u596/dkhugh3s/002_zps1fd0e869.jpg
  16. Thanks for the great pic's Mr.Blonde, and...

    Thanks for the great pic's Mr.Blonde, and everyone else who contributed to the event.

    The Peter Carey Rubicon looks amazing, smash hit for sure, would of liked an in-hand pic of that one.
    ...
  17. Not sure why caliber would make a difference, if...

    Not sure why caliber would make a difference, if they make good guns they make good guns? NEA have 308 and 300ACC/blackout uppers, not sure about 762, although you'd have a much better selection...
  18. Replies
    27
    Views
    729

    Got 1k CCI stingers lying around, you guys in the...

    Got 1k CCI stingers lying around, you guys in the states have no idea how good you have it, can't believe someone is complaining about $45 for 500, I wish I could pay that!!!!!!

    Current price here...
  19. Replies
    1,744
    Views
    66,912

    Yeah mate, thats the one, the "hot sister" :),...

    Yeah mate, thats the one, the "hot sister" :), cruwear blade, RIL, cuscadi micarta and gitd backspacer.

    old pic off the mod thread...
  20. Replies
    1,744
    Views
    66,912

    Its pretty much a Ti millie, with the liner lock...

    Its pretty much a Ti millie, with the liner lock from my cruwear model.
  21. Replies
    1,744
    Views
    66,912

    Not my pockets, but something awesome happened...

    Not my pockets, but something awesome happened today;

    My girlfriend has been doing a lot of food prep at her work lately, (she usually carries a blue delica and ladybug hawkbill), today she came...
  22. what about the moon delica ...

    what about the moon delica

    http://tomsachs.com/item/nasa-knife
  23. Replies
    45
    Views
    1,663

    Parhelion thanks for sharing your views, I have...

    Parhelion thanks for sharing your views, I have been following the situation with great interest, the political games in Ukraine over the past few years have been quite dramatic. Western media is...
  24. Replies
    5
    Views
    189

    Yeah but not remotely, you might be able to get...

    Yeah but not remotely, you might be able to get it working right by adjusting the tension on the screws, pivot and stop pin especially, try rotate the stop pin into a few different positions as well,...
  25. Replies
    5
    Views
    189

    I haven't had much trouble sharpening paras and...

    I haven't had much trouble sharpening paras and millies, foam tape to hold the blade square, you need to pack it out to match the thickness, so double it up as the blade thins out, the hardest part...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4