Search:

Type: Posts; User: w3tnz; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    79
    Views
    1,505

    Ignaz, your point of view defies logic, arguing...

    Ignaz, your point of view defies logic, arguing one firearm is more dangerous than another because of its appearance and or status in pop culture/history is irrational to say the least.

    I know...
  2. Replies
    51
    Views
    1,316

    Poll: +1 :)

    +1

    :)
  3. Replies
    46
    Views
    1,949

    I used spyderco fine and ultra fine stones for...

    I used spyderco fine and ultra fine stones for the union jack, and some LBK's for the stars of the southern cross, thanks for the contest !
    ...
  4. Replies
    3,579
    Views
    895,354

    If I could choose any, a santafe red white blue,...

    If I could choose any, a santafe red white blue, or MOP bug inlay :D I was thinking one of the more natural inlays, but the CF is growing on me.

    I think what I paid for the kiwi was reasonable,...
  5. Thread: Show your EDC

    by w3tnz
    Replies
    2,247
    Views
    1,110,612

    http://i1323.photobucket.com/albums/u596/dkhugh3s/...

    http://i1323.photobucket.com/albums/u596/dkhugh3s/edc140614_zps37a38329.jpg
  6. Replies
    3,579
    Views
    895,354

    I finally managed to get my mitts on a C75 kiwi,...

    I finally managed to get my mitts on a C75 kiwi, thanks to a lead from an edcf member, carbon fiber was not my first choice for inlay, but I won't complain :)
    ...
  7. Replies
    93
    Views
    2,101

    Poll: I feel the same way about the top 3 favourite...

    I feel the same way about the top 3 favourite handle colours !

    At least I still have my grey one.

    :)
  8. Replies
    93
    Views
    2,101

    Poll: Tan or white Superblue or vg10 :)

    Tan or white

    Superblue or vg10

    :)
  9. Replies
    4
    Views
    201

    Or just put some washers between the screws and...

    Or just put some washers between the screws and the clip.
  10. Replies
    0
    Views
    89

    help finding spyderco kiwi

    Hey forumites, I'm after some help finding a first gen locking kiwi, have been looking for about 2 years with no real luck.
    I can't and won't use eBay, being international makes it difficult as most...
  11. Replies
    17
    Views
    420

    They supposedly use Sandvik L6 and run it about...

    They supposedly use Sandvik L6 and run it about 50 something hrc.

    This one will be going back into a white handle, the pink pants belong to Travis :D
  12. Thread: Flat Broke....

    by w3tnz
    Replies
    15
    Views
    901

    If you boiled them, you could of had red soup for...

    If you boiled them, you could of had red soup for the starter :D
  13. Replies
    17
    Views
    420

    Thanks Travis, looks like a great job, should be...

    Thanks Travis, looks like a great job, should be able to get my salami paper thin now :)
  14. Cuscadi can make anything if you got the ca$h.

    Cuscadi can make anything if you got the ca$h.
  15. Replies
    11
    Views
    251

    I have roughly illustrated what I was trying to...

    I have roughly illustrated what I was trying to describe, its the only problem I have had with the wicked edge system, I don't use an angle cube because I have my vice mounted to a chopping board and...
  16. Replies
    11
    Views
    251

    I tried to explain this in your other thread but...

    I tried to explain this in your other thread but perhaps it was unclear, your problem sharpening a blade as thick as a sykco is caused by the left side of the vice being static. When you clamp a...
  17. Thread: Techno concerns

    by w3tnz
    Replies
    23
    Views
    789

    There was at least 2 reported cases of techno...

    There was at least 2 reported cases of techno lock slip on this forum alone, but don't let that discourage you from buying one. Not a design fault, just a couple that weren't made quite right and...
  18. Replies
    15
    Views
    565

    The detent is nothing more than a ball, that...

    The detent is nothing more than a ball, that seats into a hole or divot in the blade, under tension of the lockbar, no magic involved. Either the lock bar was over bent in MFG causing excess tension,...
  19. Replies
    15
    Views
    565

    This was brought up a few times, you might be...

    This was brought up a few times, you might be unlucky, but most of the time the detent is not to blame. Because the techno is so small your fingers naturally puts pressure against the lock bar when...
  20. Replies
    29
    Views
    1,130

    A bit of lint or dirt won't accelerate wear on...

    A bit of lint or dirt won't accelerate wear on steel, not lubricating the moving parts of your knife will however.. you should be cleaning it before anything like that becomes an issue in any case....
  21. Replies
    4
    Views
    142

    LC200N on the tusk..

    LC200N on the tusk..
  22. Replies
    11
    Views
    456

    I'm nearly out of my stock of 10wt, really good...

    I'm nearly out of my stock of 10wt, really good all purpose lubricant, have been using it on my bike and rifle lately. I might buy the 3 pack of applicators to try, mix up etc, but the 10wt has been...
  23. Replies
    8
    Views
    290

    There is a bit of play in the slots, its normal....

    There is a bit of play in the slots, its normal. You could put a rubber band around the top of the stones, it will bring the angle down a touch and stop the rods from moving.
  24. Thread: More Beans!

    by w3tnz
    Replies
    5
    Views
    222

    Looks good man :)

    Looks good man :)
  25. I have done it on a couple of my knives, when the...

    I have done it on a couple of my knives, when the rough surface inside the hole has started to corrode, but don't worry about it otherwise. I don't chamfer the edge, leave it sharp.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4