Mule care for dummies
-
- Member
- Posts: 34
- Joined: Tue Jun 28, 2022 11:43 am
Mule care for dummies
Looking for a little guidance on how to handle rust underneath scales.
Located in warm coastal area with higher humidity (five miles inland) and they are stored in climate controlled area. Mules are used in kitchen work, box cutting, woodwork, camping, hunting, etc but are usually home inside at the end of day.
Specifics: Rex 76, SRS-13/SUS 405, M398, AEB-L with Halpern G-10 scales
Rex 76 got scales first because paracord + wash and dry produced hot spots quickly. Now lives in a leather sheath in a pantry cabinet and needs an occasional wipe with mineral oil.
SRS-13/SUS405 and M398 have a thin coat of mineral oil between scales and handle after upgrading to scales two months ago. Pulled them apart today and have tiny rust spots and oil is rust colored in areas. Checked AEB-L and.good so far but use it less.
Blades are carefully washed and dried, placed on the windowsill in the sun to dry after. Try not to get the handle wet with work/during wash, but you know...
Not necessarily looking to epoxy them yet. So should I expect to have to do this every two months until I decide which scale should be with which mule forever?
Thanks in advance
Located in warm coastal area with higher humidity (five miles inland) and they are stored in climate controlled area. Mules are used in kitchen work, box cutting, woodwork, camping, hunting, etc but are usually home inside at the end of day.
Specifics: Rex 76, SRS-13/SUS 405, M398, AEB-L with Halpern G-10 scales
Rex 76 got scales first because paracord + wash and dry produced hot spots quickly. Now lives in a leather sheath in a pantry cabinet and needs an occasional wipe with mineral oil.
SRS-13/SUS405 and M398 have a thin coat of mineral oil between scales and handle after upgrading to scales two months ago. Pulled them apart today and have tiny rust spots and oil is rust colored in areas. Checked AEB-L and.good so far but use it less.
Blades are carefully washed and dried, placed on the windowsill in the sun to dry after. Try not to get the handle wet with work/during wash, but you know...
Not necessarily looking to epoxy them yet. So should I expect to have to do this every two months until I decide which scale should be with which mule forever?
Thanks in advance
- Traditional.Sharpening
- Member
- Posts: 286
- Joined: Thu Mar 02, 2023 12:29 am
Re: Mule care for dummies
Mineral oil is, IMO, better than nothing but closer to being a wive's tale as an actual rust preventative. You need something which has wax in it to really cut down on rust or other chemical that functions similarly. If you don't mind chemical smell and caution applying, as it's basically toxic dry-cleaning chemicals, then Eezox works well assuming correct application.
I have seen folks that don't understand it's correct use apply it like other oils and that's just a terrible idea. It NEEDS to be applied VERY lightly and allowed to dry (takes a few hours, wipe excess if still not dry after a few hours). It leaves a dry film protectant/lubricant behind which is claimed 'food safe' when dry, I do not doubt this as there's truly virtually no product left after drying as the carrier solvent evaporates when dry.
If you want to go wax route, then you could use something like Renaissance Wax or Odie's Oil
https://odiesoil.com/finishes/
.
https://www.woodcraft.com/products/renaissance-wax
I have seen folks that don't understand it's correct use apply it like other oils and that's just a terrible idea. It NEEDS to be applied VERY lightly and allowed to dry (takes a few hours, wipe excess if still not dry after a few hours). It leaves a dry film protectant/lubricant behind which is claimed 'food safe' when dry, I do not doubt this as there's truly virtually no product left after drying as the carrier solvent evaporates when dry.
If you want to go wax route, then you could use something like Renaissance Wax or Odie's Oil
https://odiesoil.com/finishes/
.
https://www.woodcraft.com/products/renaissance-wax
- standy99
- Member
- Posts: 2219
- Joined: Sat Jul 22, 2017 11:07 am
- Location: Between Broome and Cairns somewhere
Re: Mule care for dummies
Find it sort of wicks the water in.
Thin liner of felt soaked in mineral oil or even better food grade Inox if you don’t mind the touch of inox smell between each side.
Live in humid central tropical Northern Australia and was the only thing that worked. Was over taking the scales off every month or two to clean the handle. Worked pretty good but still after a few months it was a slight clean up compared to what it was like without felt.
Have switched to epoxied scales due to this reason.
Usually a new mule I use removable scales for a bit until I have made a forever handle.
Thin liner of felt soaked in mineral oil or even better food grade Inox if you don’t mind the touch of inox smell between each side.
Live in humid central tropical Northern Australia and was the only thing that worked. Was over taking the scales off every month or two to clean the handle. Worked pretty good but still after a few months it was a slight clean up compared to what it was like without felt.
Have switched to epoxied scales due to this reason.
Usually a new mule I use removable scales for a bit until I have made a forever handle.
Im a vegetarian as technically cows are made of grass and water.
Re: Mule care for dummies
I have become a fan of using a coating of chapstick because I use my knives for food prep at times. For storage, I do chapstick and zip lock bags rolled up to remove excess air. You can also use those packets that come with packing to reduce moisture in the container of choice.
Mule Team Army 001
MNOSD 008
Stable Mules; Z-Max, Z-Wear, Magna Cut, SRS13, Rex 76, Rex T15.
MNOSD 008
Stable Mules; Z-Max, Z-Wear, Magna Cut, SRS13, Rex 76, Rex T15.
-
- Member
- Posts: 92
- Joined: Thu May 04, 2023 1:00 pm
Re: Mule care for dummies
For what it's worth, I'm on the same bi-monthly tear down and rust spot removal. I also do a coat of oil underneath the scales. Even the AEB-L gets spots for me, although I stop at wiping dry before sheathing and an oil wipe each week of regular use. For the tool steels, I've been considering cerakote to keep the service intervals longer. Even with good blade hygiene, if you can see the ocean it is probably already going to work on your steels, haha.
Re: Mule care for dummies
The problem is with the area between the handle and scales. Moisture eventually migrates in, causing rust. The problem is that if moisture can migrate in, all these "blade treatments" will eventually migrate out. The thinner the treatment, the more quickly it will migrate out. So if you want to go with some kind of blade treatment, go with axle grease. It will take longer to ooze out.
Why not go for something a little more permanent, but that can be removed once you decide on exactly what you want to do permanently with the knife. I'm thinking about Rustoleum. Spray the handle, let it dry, and assemble the knife. Overspray will be easy to clean up. If you decide to do something else with the knife, the old paint will be relatively easy to remove.
- legOFwhat?
- Member
- Posts: 3152
- Joined: Mon Jul 09, 2018 5:58 am
- Location: Kentucky; Earth
Re: Mule care for dummies
I've finally migrated to making permanent handles but still keep a few removable. This was after a couple of months neglect during summer walking. Last application was Ballistol but oil and sweat from my hands crept in.
-Larry
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
- standy99
- Member
- Posts: 2219
- Joined: Sat Jul 22, 2017 11:07 am
- Location: Between Broome and Cairns somewhere
Re: Mule care for dummies
Yep….whole reason I went to permanent scales. Even the lesser prone to rust variations had similar rust.legOFwhat? wrote: ↑Mon Sep 11, 2023 1:58 pmI've finally migrated to making permanent handles but still keep a few removable. This was after a couple of months neglect during summer walking. Last application was Ballistol but oil and sweat from my hands crept in.
Removable Scales seem to wick the water in. Got sick of removing scales.
Not hard to epoxy removable scales on and even place a coloured liner on before hand
Im a vegetarian as technically cows are made of grass and water.
- legOFwhat?
- Member
- Posts: 3152
- Joined: Mon Jul 09, 2018 5:58 am
- Location: Kentucky; Earth
Re: Mule care for dummies
Definitely, just make sure there is enough threads to connect to the barrels after the liners...standy99 wrote: ↑Mon Sep 11, 2023 2:29 pmYep….whole reason I went to permanent scales. Even the lesser prone to rust variations had similar rust.legOFwhat? wrote: ↑Mon Sep 11, 2023 1:58 pmI've finally migrated to making permanent handles but still keep a few removable. This was after a couple of months neglect during summer walking. Last application was Ballistol but oil and sweat from my hands crept in.
Removable Scales seem to wick the water in. Got sick of removing scales.
Not hard to epoxy removable scales on and even place a coloured liner on before hand
-Larry
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
Hebrews 13:6 So we may boldly say: “The Lord is my helper; I will not fear. What can man do to me?”
MNOSD #0049
- standy99
- Member
- Posts: 2219
- Joined: Sat Jul 22, 2017 11:07 am
- Location: Between Broome and Cairns somewhere
Re: Mule care for dummies
Yes probably good to get the 0.02” G10 liners (or .5mm for the rest of the world that use the easier Metric system )legOFwhat? wrote: ↑Mon Sep 11, 2023 5:12 pmDefinitely, just make sure there is enough threads to connect to the barrels after the liners...standy99 wrote: ↑Mon Sep 11, 2023 2:29 pmYep….whole reason I went to permanent scales. Even the lesser prone to rust variations had similar rust.legOFwhat? wrote: ↑Mon Sep 11, 2023 1:58 pmI've finally migrated to making permanent handles but still keep a few removable. This was after a couple of months neglect during summer walking. Last application was Ballistol but oil and sweat from my hands crept in.
Removable Scales seem to wick the water in. Got sick of removing scales.
Not hard to epoxy removable scales on and even place a coloured liner on before hand
https://www.makermaterialsupply.com/col ... ant-colors
Im a vegetarian as technically cows are made of grass and water.
Re: Mule care for dummies
I’ve had good success fighting rust by slathering on a coat of frog lube. It’s safe for food but if using a handle material that is absorbent, it will absorb it. That could be a positive tho.
Re: Mule care for dummies
I just removed the paracord wrap on my AEB-L mule, it’s been wrapped since shortly after the AEB-L mules dropped. No rust at all! All I do is spray the paracord with Froglube oil every once in a while. The Froglube drys with no oily feel at all. I’ve also noticed that Froglube oil easily seeps into G10 scales. Oh and I live in the PNW so the knives get exposed to water and salt water often.barnaclesonaboat wrote: ↑Mon Sep 11, 2023 12:00 pmFor what it's worth, I'm on the same bi-monthly tear down and rust spot removal. I also do a coat of oil underneath the scales. Even the AEB-L gets spots for me, although I stop at wiping dry before sheathing and an oil wipe each week of regular use. For the tool steels, I've been considering cerakote to keep the service intervals longer. Even with good blade hygiene, if you can see the ocean it is probably already going to work on your steels, haha.
Greg
* EDC - - - PM2 - S45VN, PM2 - Crucarta, Native 5 - CRUWEAR, Manix 2 LW - CPM M4
Mules in current use M398 and K294
* EDC - - - PM2 - S45VN, PM2 - Crucarta, Native 5 - CRUWEAR, Manix 2 LW - CPM M4
Mules in current use M398 and K294
- VeraX_Knives
- Member
- Posts: 92
- Joined: Mon Jun 06, 2022 2:36 pm
- Location: Bethel Park, Pennsylvania
Re: Mule care for dummies
Id really like to do some real life research on tribocorrosion resistance instead of the typical scientific tests that.. I'm not in the city but I'm not in the country either, so, basically all of the adsorption type fails I would have to actually try to make happen with.. let's be real, as pure as "pure" gets gases. I mean really id like to try it in China or India with hydrocarbon emissions but that's just not really feasible for me to do. I know absolutely nobody that lives.. within eyesight of the ocean **** the .. closest is probably the Gulf and around Houston inland in Texas, where that really important port my brain can't remember is that deals with the offshore oil processing. Jesus Christ that's going to annoy me. Port Arthur. Is where id really like to do this but since my brain is too stupid to remember it's name - thinking uh whadda what oh right lol - I don't think that I really deserve to have the permission to even go there without being shot personally oh ya you cocked this one up good Jason Ward. Yes I laugh at myself. I'm easily amused, I'm an American hillbilly what do you expect here!.
Mainly my intentions here are for knowing how my heat treatments and finishes will react to different environments and whatnot. I know the science type testing but I can't honestly say that I know.. what happens over 10 years with use etcetera. I theoretically do but that's pretty worthless for me honestly. Actually, as I'm thinking I . Don't recall Spyderco doing a rex 86/z-max blade. Probably for this exact reasoning plus it is an utter pain in the *** to work with.
Anyone with any long term information on that specific alloy would be appreciated although I know that I am.. aiming for an A shot at 50yds with a pistol and I'm lucky if I get a D. I'm expecting to miss a few here.
Mainly my intentions here are for knowing how my heat treatments and finishes will react to different environments and whatnot. I know the science type testing but I can't honestly say that I know.. what happens over 10 years with use etcetera. I theoretically do but that's pretty worthless for me honestly. Actually, as I'm thinking I . Don't recall Spyderco doing a rex 86/z-max blade. Probably for this exact reasoning plus it is an utter pain in the *** to work with.
Anyone with any long term information on that specific alloy would be appreciated although I know that I am.. aiming for an A shot at 50yds with a pistol and I'm lucky if I get a D. I'm expecting to miss a few here.
••• You say E = mc² × I argue E² = m²c⁴ + p²c² •••
Jason Ward • shockey01@gmail.com • +1 412-726-8610 • My Discord
Jason Ward • shockey01@gmail.com • +1 412-726-8610 • My Discord
- standy99
- Member
- Posts: 2219
- Joined: Sat Jul 22, 2017 11:07 am
- Location: Between Broome and Cairns somewhere
Re: Mule care for dummies
Mule Number 29VeraX_Knives wrote: ↑Wed Apr 24, 2024 10:24 pmDon't recall Spyderco doing a rex 86/z-max blade. Probably for this exact reasoning plus it is an utter pain in the *** to work with.
MT29 - Steel: Z-Max PM | Released Jun 2021 | Quantity: Approximately 550
MT30 - Steel: Z-Wear PM | Released Aug 2021 | Quantity: Approximately 500
Im a vegetarian as technically cows are made of grass and water.
- VeraX_Knives
- Member
- Posts: 92
- Joined: Mon Jun 06, 2022 2:36 pm
- Location: Bethel Park, Pennsylvania
Re: Mule care for dummies
Same year I bought mine thank you much sirstandy99 wrote: ↑Thu Apr 25, 2024 7:17 amMule Number 29VeraX_Knives wrote: ↑Wed Apr 24, 2024 10:24 pmDon't recall Spyderco doing a rex 86/z-max blade. Probably for this exact reasoning plus it is an utter pain in the *** to work with.
MT29 - Steel: Z-Max PM | Released Jun 2021 | Quantity: Approximately 550
MT30 - Steel: Z-Wear PM | Released Aug 2021 | Quantity: Approximately 500
••• You say E = mc² × I argue E² = m²c⁴ + p²c² •••
Jason Ward • shockey01@gmail.com • +1 412-726-8610 • My Discord
Jason Ward • shockey01@gmail.com • +1 412-726-8610 • My Discord