Stretch 2 pivot screw washer size
-
- Member
- Posts: 8
- Joined: Mon Apr 15, 2024 6:39 pm
Stretch 2 pivot screw washer size
Anyone know the size of the tiny washer that goes with the pivot screw on the stretch 2 k390? I seem to have lost mine somehow.
Thanks in advance!
Thanks in advance!
Re: Stretch 2 pivot screw washer size
The Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.
I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.
I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.
-
- Member
- Posts: 8
- Joined: Mon Apr 15, 2024 6:39 pm
Re: Stretch 2 pivot screw washer size
Thanks, do you know the washer size?cjk wrote: ↑Wed May 15, 2024 7:52 pmThe Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.
I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.
Re: Stretch 2 pivot screw washer size
not offhand, but here's where you can buy some.PlungeGrind wrote: ↑Thu May 16, 2024 5:50 amThanks, do you know the washer size?cjk wrote: ↑Wed May 15, 2024 7:52 pmThe Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.
I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.
https://www.knivesplus.com/replacement- ... ndela.html
iirc, there was a washer size thread on this forum.
-
- Member
- Posts: 8
- Joined: Mon Apr 15, 2024 6:39 pm
Re: Stretch 2 pivot screw washer size
Those are the washers for the pivot. I’m looking for the washer that goes on the pivot screw.cjk wrote: ↑Thu May 16, 2024 8:26 pmhttps://www.knivesplus.com/replacement- ... ndela.htmlPlungeGrind wrote: ↑Thu May 16, 2024 5:50 amThanks, do you know the washer size?cjk wrote: ↑Wed May 15, 2024 7:52 pmThe Delica, Endela, and Endura all use the same washers. I'd bet the Stretch 2 does too. There are replacements available in the aftermarket.
I'm sure Spyderco can supply a replacement, but it's an internal part, so you'd probably need to send your knife in for service. I believe their policy is that they don't send out internal parts.
Have you disassembled a stretch?
Re: Stretch 2 pivot screw washer size
thread about Delica washer size which I expect to be the same:
viewtopic.php?t=64451
quoted post with measurements:
Did you lose both? If you lost one, you could measure the other.
viewtopic.php?t=64451
quoted post with measurements:
Michael Janich wrote: ↑Mon Jul 21, 2014 6:48 amOutside diameter 0.316"
Inside diameter 0.161"
Thickness 0.0035"
Stay safe,
Mike
Did you lose both? If you lost one, you could measure the other.
-
- Member
- Posts: 8
- Joined: Mon Apr 15, 2024 6:39 pm
Re: Stretch 2 pivot screw washer size
Again I am not looking for a pivot washer, I am looking for the pivot screw washer. Do you l is what size the pivot screw washer is?cjk wrote: ↑Fri May 17, 2024 6:00 amthread about Delica washer size which I expect to be the same:
viewtopic.php?t=64451
quoted post with measurements:Michael Janich wrote: ↑Mon Jul 21, 2014 6:48 amOutside diameter 0.316"
Inside diameter 0.161"
Thickness 0.0035"
Stay safe,
Mike
Did you lose both? If you lost one, you could measure the other.
-
- Member
- Posts: 291
- Joined: Fri Sep 24, 2004 10:33 am
- Location: Country Knives - Intercourse, PA USA
- Contact:
Re: Stretch 2 pivot screw washer size
https://www.spyderco.com/service-suppor ... ty-repair/
Toll-free: 800-525-7770 X 3
customerservice@spyderco.com
Ask the source! This department was created to be of assistance.
nb
Toll-free: 800-525-7770 X 3
customerservice@spyderco.com
Ask the source! This department was created to be of assistance.
nb
-
- Member
- Posts: 8
- Joined: Mon Apr 15, 2024 6:39 pm
Re: Stretch 2 pivot screw washer size
Yes, if they would only reply that would be great, but alas every time I email them, crickets.N. Brian Huegel wrote: ↑Sat May 18, 2024 7:35 amhttps://www.spyderco.com/service-suppor ... ty-repair/
Toll-free: 800-525-7770 X 3
customerservice@spyderco.com
Ask the source! This department was created to be of assistance.
nb
Unfortunately customer service at Spyderco is becoming as subpar as BM.
Re: Stretch 2 pivot screw washer size
Oh that washer! It appears to be sometimes included and sometimes not. I've had several K390 Delicas. Some of them had it and some of them didn't.
I do have a K390 Stretch 2.
I measured with a cheap set of digital calipers.
The washer is tiny. It's fairly difficult to measure, so these are approximate. I dropped it a lot while measuring. The thickness was the easiest to measure.
outer diameter (inches/mm): .224 / 5.5
inner diameter: .082 / 2.06
thickness: .013 / .32
It's the same washer as is sometimes on a Delica/Endura and sometimes not. Given that it's sometimes included and sometimes not, I wouldn't sweat too much that it's missing.
I compared the washer on my K390 Stretch 2 and the one on an old ZDP-189 Delica. They were the same as far as I could tell.
I do have a K390 Stretch 2.
I measured with a cheap set of digital calipers.
The washer is tiny. It's fairly difficult to measure, so these are approximate. I dropped it a lot while measuring. The thickness was the easiest to measure.
outer diameter (inches/mm): .224 / 5.5
inner diameter: .082 / 2.06
thickness: .013 / .32
It's the same washer as is sometimes on a Delica/Endura and sometimes not. Given that it's sometimes included and sometimes not, I wouldn't sweat too much that it's missing.
I compared the washer on my K390 Stretch 2 and the one on an old ZDP-189 Delica. They were the same as far as I could tell.
Re: Stretch 2 pivot screw washer size
Hi, PlungeGrind:PlungeGrind wrote: ↑Sat May 18, 2024 2:20 pmYes, if they would only reply that would be great, but alas every time I email them, crickets.N. Brian Huegel wrote: ↑Sat May 18, 2024 7:35 amhttps://www.spyderco.com/service-suppor ... ty-repair/
Toll-free: 800-525-7770 X 3
customerservice@spyderco.com
Ask the source! This department was created to be of assistance.
nb
Unfortunately customer service at Spyderco is becoming as subpar as BM.
I checked with W&R, and they haven't received any emails from you (at least not from the email address you use on the forum). Please send me a PM with your contact information and I can have them check again.
Kristi
There is nothing more important than this one day.
-
- Member
- Posts: 8
- Joined: Mon Apr 15, 2024 6:39 pm
Re: Stretch 2 pivot screw washer size
Awesome! Thanks for the info, that’s exactly what I was looking for. I had several disassembled at once so maybe I didn’t lose it after all.cjk wrote: ↑Mon May 20, 2024 2:28 pmOh that washer! It appears to be sometimes included and sometimes not. I've had several K390 Delicas. Some of them had it and some of them didn't.
I do have a K390 Stretch 2.
I measured with a cheap set of digital calipers.
The washer is tiny. It's fairly difficult to measure, so these are approximate. I dropped it a lot while measuring. The thickness was the easiest to measure.
outer diameter (inches/mm): .224 / 5.5
inner diameter: .082 / 2.06
thickness: .013 / .32
It's the same washer as is sometimes on a Delica/Endura and sometimes not. Given that it's sometimes included and sometimes not, I wouldn't sweat too much that it's missing.
I compared the washer on my K390 Stretch 2 and the one on an old ZDP-189 Delica. They were the same as far as I could tell.
Thanks a million!